Tasc Machine Data

Number	Description	Initial Value	Units	PW	TLF2000	TLF2700	TLF3200	TLF3600	TLF4000	TLF5000	TLF6003	TLF7003	TLF8003	TLF6000	TLF8000	TLF12000	TCFL2510	TCF3000L	TCF1OEM	TCF1000OEM	Notes
60	Exchange interval diaphragm vacuum pump 2	10000 a	h	1	0	0	0	0	0	0	0	0	0	15000	15000	15000	0	0	0	0	Starting with V2.7.1: Value for recommendation to exchange the membrane vacuum p More ...
61	Switching frequency pulse to CW for BCD-SS	50.00	kHz	0	50.00	50.00	50.00	50.00	50.00	50.00	50.00	50.00	50.00	50.00	50.00	50.00	50.00	50.00	50.00	50.00	As suggested by Control, or per customer request.
62	Permanent deactivation time for laser power monitoring	0.250	sec	1	0.250	0.250	0.250	0.250	0.250	0.250	0.250	0.250	0.250	0.250	0.250	0.250	0.250	0.250	0.250	0.250	Disabling time is active if the nominal power does not change.
63	Deactivation time laser power mointoring for nominal power changes.	2.000	sec	1	2.000	2.000	2.000	2.000	2.000	2.000	2.000	2.000	2.000	4.000	4.000	4.000	2.000	2.000	2.000	2.000	small L-measuring head = 2,0sec; large L-measuring head = 4,0sec
64	Lower limit power monitoring	0	W	0	1700	2300	2700	3500	3500	4400	5300	???	???	5300	7000	10000	1600	1600	1600	800	Up to now only type-dependent, lower limit power monitoring with maximal laser n More ...
65	Upper limit power monitoring	0	W	0	2500	3400	4000	5000	5000	6000	7500	???	???	7500	10000	15000	2400	2400	2400	1500	type-dependent
66	Maximum pulse duty factor	100.00	%	1	100.00	100.00	100.00	100.00	100.00	100.00	100.00	100.00	100.00	100.00	100.00	100.00	100.00	100.00	100.00	100.00
67	Vacuum pump oil change interval	0	h	1	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	With membrane vacuum pumps, this value = 0, With rotary slide valve - vacuum pu More ...
68	Sensitivity analog LLS	0.02	%	0	0.20	0.20	0.20	0.20	0.20	0.20	0.20	0.20	0.20	0.20	0.20	0.20	0.20	0.20	0.20	0.20	As suggested by Control
69	Filter weighing factor for analog LLS	0.950	digit	0	0.950	0.950	0.950	0.950	0.950	0.950	0.950	0.950	0.950	0.950	0.950	0.950	0.950	0.950	0.950	0.950	As suggested by Control
70	Power regulation active	0	digit	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	Starting with V3.2.2: Regulator Off/On = (0/1) Open regulator = 2
71	Power regulation control amplification	0.02	%	1	0.02	0.02	0.02	0.02	0.02	0.02	0.02	0.02	0.02	0.02	0.02	0.02	0.00	0.00	0.00	0.00	Starting with V3.2.2: Low pass f(n) = x(n) * weighting + f(n-1) * (1-weighting) More ...
72	Power regulation reset time	1 Ab V03.	%	1	0.0025	0.0025	0.0025	0.0025	0.0025	0.0025	0.0025	0.0025	0.0025	0.0025	0.0025	0.0025	0.0025	0.0025	0.0025	0.0025	Starting with V3.2.2: Delta_gating ratio, so that the regulation deviation can b More ...
73	Delay for power control	0.000	sec	1	2.000	2.000	2.000	2.000	2.000	2.000	2.000	2.000	2.000	2.000	2.000	2.000	2.000	2.000	2.000	2.000	Starting with V3.2.2: Time delay of the laser power regulation after nominal val More ...
74	Laser number	56	digit	1	>0	>0	>0	>0	>0	>0	>0	>0	>0	>0	>0	>0	>0	>0	>0	>0	individually
75	Further calibration lines active	0	digit	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	Starting with V2.7.2: 0=standard calibration as previously. 4 Characteristic cu More ...
76	Minimum laser power during calibration	30.00	W	1	30.00	30.00	30.00	30.00	30.00	30.00	30.00	30.00	30.00	30.00	30.00	30.00	30.00	30.00	30.00	30.00	Starting with V2.7.2: Value is used as interruption condition for the automatic More ...
77	Upper limit nominal power	0	W	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	Starting with V3.0.6: Limiting the nominal power to a maximal value for protecti More ...
78	Water changing interval	4320	h	1	4320	4320	4320	4320	4320	4320	4320	4320	8760	4320	4320	4320	4320	4320	4320	8760	Starting 05/25/2007, reduced from 4380h to 4320h Starting with V4.2.x new stan More ...
79	Laser On/Off active via dig. input	0	digit	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	Starting with Version V3.0.x implemented Starting with Version V3.5.2: reaction More ...

Any reference to TRUMPF machines, part numbers etc, are for reference only. Call for current pricing.